地址: 河北省泊头市道东街88号
电话: 0317-8185077
0317-8263980
0317-8223128
传真: 0317-8265584
E-mail: hbydby@126.com

公司新闻

你所在位置:首页 -  - 新闻中心 - 公司新闻 
输送柴油泵KCB483.3铜轮防爆齿轮泵助力锦州宏泰化工
发布时间:2014-12-30 9:54:32 点击次数:

      KCB483.3齿轮泵流量29m3/h(483.3L/min),压力0.36Mpa,吸入真空高度3米,效率42%,口径70,配用电机7.5kw-4或者11kw-4.

      KCB483.3齿轮泵产品图片

      输送柴油油使用铜轮防止在输送过程中,金属摩擦产生火花,发生燃烧.所以在输送汽柴油工况,我公司推荐客户使用铜轮齿轮泵.

        KCB齿轮油泵在输油系统中可用作传输、增压泵;KCB gear oil pump in the oil system can be used as a transport, booster pump;

   在燃油系统中可用作输送、加压、喷射的燃油泵;In the fuel system can be used as a transport, pressure, jet fuel pump;

   在一切工业领域中,均可作润滑油泵用。In all industrial areas, can be used as lubricating oil pump.

   KCB齿轮泵主要有齿轮、轴、泵体、安全阀、轴端密封所组成。齿轮经热处理有较高的硬度和强度,与轴一同安装在可更换的轴套内运转。泵内全部零件的润滑均在泵工作时利用输出介质而自动达到。KCB gear pump are mainly gear, shaft, pump body, valve, shaft end seal. Gear after heat treatment with high hardness and strength, and shaft installed in the replaceable shaft sleeve. In all parts of the lubrication pump are pump work automatically to achieve using the output media.

   泵内有设计合理的泄油和回油槽,是齿轮在工作中承受的扭矩力最小,因此轴承负荷小,磨损小,泵效率高。Pump is the drainage and back into the groove of reasonable design, is a gear in the work under the minimum torque force, so the bearing load is small, wear small, pump with high efficiency.

   泵设有安全阀作为超载保护,安全阀的全回流压力为泵额定排除压力的1.5倍,也可在允许排出压力范围内根据实际需要另外调整。但注意本安全阀不能作减压阀的长期工作,需要时可在管路上另行安装。从主轴外伸端向泵看,为顺时针旋转。Pump is equipped with safety valve as overload protection, the total reflux pressure relief valve is rated pump out pressure of 1.5 times, also can allow discharge pressure range according to actual needs and adjust. But note that this cannot be a long-term work pressure reducing valve, relief valve can be installed in the piping shall be separately when necessary. To pump from the main shaft overhang end to see, for clockwise.

 

 

   流量:1.1m3/h-600m3/h压力:0.28MPa--2.5MPa  Traffic: 1.1 m3 / h - 600 m3 / h pressure: 0.28 MPa, 2.5 MPa 

   主要用于油田、油库、港口、码头、船舶等大流量输油,卸油!Mainly used in oil fields, oil depot, ports, docks, ship big flow like oil, oil unloading!

   应用范围:KCB/2CY型齿轮输油泵适用于输送粘度在300c.s.t以下的各种油类,如原油、柴油、润滑油、动植物油等。配用铜齿轮可输送低闪点液体,如汽油、苯等。介质温度不超过70℃,耐高温油泵的使用温度不超过300℃。本泵身带有安全阀,超载时起安全作用。轴封有骨架油封、机械密封、填料密封三种型式,订货注明。KCB齿轮润滑泵主要用于各种机械设备中的润滑系统中输送润滑油,适用于输送粘度在10oE(75c.s.t)以下,温度在300℃以下的具有润滑性的油料,不锈钢齿轮泵可输送食用油料、饮料等。轴封有骨架油封、机械密封、填料密封三种型式.Scope of application: KCB type / 2 cy gear oil pump is suitable for conveying viscosity at 300 c. S.t under various oil, such as crude oil, diesel oil, lubricating oil, animal and plant oil. With copper gear can handle liquid low flash point, such as gasoline, benzene, etc. Medium temperature does not exceed 70 ℃, the use of high temperature resistant oil pump temperature does not exceed 300 ℃. When the pump body with a safety valve, overloading security role. Shaft seal skeleton oil seal, mechanical seal, packing three type, indicate the order. KCB gear lubrication pump is mainly used for all kinds of mechanical equipment of conveying lubricating oil in the lubricating system, suitable for conveying viscosity in 10 oe (below 75 c. S.t), the temperature is below 300 ℃ with lubrication oil, stainless steel pump can transport edible oil, beverage and so on. Shaft seal skeleton oil seal, mechanical seal, packing three types.

   KCB齿轮泵安装说明:1、安装泵的地点应足够宽敞,以方便检修工作。2、泵安装的好坏,对泵的平稳运行和使用寿命有很重要的影响,所以安装校正工作必须仔细地进行,不得草率行事。3、泵吸入管的安装高度、长度和管径应满足计算值,力求简短,减少不必要的损失(如弯头等);并保证泵在工作时,不超过其允许汽蚀余量。4、吸入和排出管路应该有支架。泵不允许承受管路的负荷。KCB gear pump installation instructions: 1, the location of the installation of pump should be spacious enough, to facilitate maintenance and repair work. The stand or fall of 2, pump installation, for the smooth running of the pump and service life have very important influence, so the installation calibration work must be carried out carefully and must not be too hasty. 3, installation height of pump suction pipe, the length and diameter should satisfy the calculated value, to short, reduce unnecessary losses, such as elbow, etc.); And ensure the pump at work, no more than the allowed NPSH. 4, suction and discharge line should be a support. Pump are not allowed to bear load of pipeline.

输送原油泵 SNH1300R42U12.1W2三螺杆泵头 山东华阳农药化工集团有限公司
沥青溶剂泵 SNH2200R42U12.1W2三螺杆泵 杭州之江有机硅化工有限公司
输送炭黑油泵 SNH2200R46E6.7W21三螺杆泵 帝人聚碳酸脂有限公司
输送脂肪酸泵 SNH280R54E6.7W21泵头 山东齐旺达集团海仲石化有限公司
炭黑油输送泵 SNH3600R46E6.7W21三螺杆泵头 内蒙古兰太实业股份有限公司
输送树胶溶液泵 G40-1V-W110单螺杆泵 中盐吉兰泰化工集团有限公司
输送燃料油泵 SNH40R38U12.1W21三螺杆泵 江苏绿陵化工集团有限公司
输送液压油泵 SNH40R38U12.1W21三螺杆泵头 山东联合化工股份有限公司
输送炼油泵 SNH40R38U12.1W2三螺杆泵头 辽宁吕氏化工(集团)有限公司
输送粘合剂泵 SNH440R46E6.7W21三螺杆泵头 浙江大东南塑胶集团公司
倒油泵 SNH440R46E6.7W21三螺杆泵 江苏省新世纪盐化集团有限责任公司
输送胶乳泵 SNH660L51U12.1W2三螺杆泵头 浙江江山化工股份有限公司
锅炉点火油泵 SNH80R46E6.7W21三螺杆泵泵头 山东海天生物化工有限公司
输送胶水泵 NYP110-RU-T1-W11高粘度泵 际华三五一七橡胶制品有限公司
热火装置点火油泵 SNH80R46E6.7W21三螺杆泵泵头 龙星化工股份有限公司
桐油输送泵 SNH80R46E6.7W21三螺杆泵泵头 河北金牛化工股份有限公司
输送润滑油泵 SNH80R46E6.7W21三螺杆泵泵头 安徽八一化工集团有限公司
输送重油泵 SNH80R46E6.7W21三螺杆泵 遵义氯碱股份有限公司
渣油装车泵 SNH940R46E6.7W21泵头 青岛红星化工集团有限责任公司
输送石油泵 SNS210R46U12.1W2立式三螺杆泵 天脊中化高平有限公司
输送矿物油泵 SPF20R38G10FW2三螺杆泵 朝阳浪马轮胎有限责任公司
无油焦油抽出泵 SPF20R38G10W2三螺杆泵头 陵县绿源化工有限责任公司
输送焦油泵 SPF20R38G10W2三螺杆泵头 重庆长寿化工有限责任公司